How do I identify my Chevy rear end?
All Chevrolet rear ends can be identified by comparing the gasket shape to an identification chart similar to the one found on Drivetrain’s differential identification page (see References). A visual chart of different GM/Chevrolet rear ends is found on Ring & Pinion’s differential types web page (see References).
What is the value of a 1964 Chevy truck?
**Figure based on a stock 1964 Chevrolet C10 1/2 Ton valued at $18,200 with OH rates with $100/300K liability/UM/UIM limits. Actual costs vary depending on the coverage selected, vehicle condition, state and other factors.
How can you tell the difference between a C10 and C20?
The obvious difference between the C10 and the C20 is that one is a half-ton and the other a three-quarter-ton truck. These classifications don’t refer to their respective curb weights, but rather to their payload capacity.
How do you find out what Differential I have?
Pop a couple of axle stands under your truck and have a look at the number of cover bolts, the distinctive shape of the cover, the number of ring gear bolts, and ring gear diameter your Ford, Dodge or Chevy differential has. They can also be identified by whether the center section is an integral or dropout design.
What does a 1964 C10 weigh?
Dimensions. The 1964 Chevy truck has a 115-inch wheelbase for the short version and 127 inches for the long bed, or long box model. It has a total curb weight of about 3,445 lbs. These trucks were on the heavy side as they were made mostly of steel.
What is a 1966 Chevy truck worth?
**Figure based on a stock 1966 Chevrolet C10 1/2 Ton valued at $18,200 with OH rates with $100/300K liability/UM/UIM limits. Actual costs vary depending on the coverage selected, vehicle condition, state and other factors.
What is a C20 Chevy?
The number designation in the Chevy C/K trucks name refers to their load capacities in a half ton (C10), three-quarter ton (C20) and one ton (C30). The C/K truck was built in either short-bed or long-bed version and is one of the most popular pickup trucks ever produced worldwide.
What engine does a C20 have?
Powertrain. The base engine was an overhead-valve V-6 displacing 262 cubic inches, or 4.3 liters, which had a four-barrel carburetor and a compression ratio of 9.3-to-1, and produced 155 horsepower. A 292-cubic-inch (4.8-liter) inline-six was also available.
What kind of rear end does a 1964 Chevy have?
This 1955-1956-1957-1958-1959-1960-1961-1962-1963-1964 Chevrolet 3.08 rear end center section is an original used two-pinion type with cast arma-steel housing. The 10-bolt differential fits all passenger cars. We have inspected the ring and pinion so as to ensure minimal ware and tare on the differentials that we sell.
What is the wheelbase of a 1964 Chevy truck?
The 1964 Chevy truck has a 115-inch wheelbase for the short version and 127 inches for the long bed, or long box model. It has a total curb weight of about 3,445 lbs. These trucks were on the heavy side as they were made mostly of steel. The exterior length is 199.5 inches and the exterior height measures 55.7 inches.
Where is the rear differential code on a 1970 Chevy?
1958-1970 Chevy Rear Differential code Identification Using the charts below, you will be able to learn alot about the rear differential in your classic full size Chevy. The gear ratio codes are located on the front passenger side of the differential as shown in the illustration below.
What kind of engine does a 1964 Chevy Silverado have?
The standard engines were 230 and 292 cubic-inch, six-cylinder engines for all two-wheel drives. In 1964, these engines were available for four-wheel drive pickups also. The 283 cubic-inch, V-8 engine was optional.
